![]() ![]() Serial.print("TempUI:TCNT1 #2 \t") Serial.println(TempUI) TempUI = TIM16_ReadTCNT1() //try to read TCNT1 using the function suggested in the Datasheetĭelay(1000) //allow TCNT1 to count for one more second which should yield TCNT1 of ~ 32000 Sei() //reenable interrupts to allow delay to put some more counts on TCNT1 TIMSK1 = (1 << OCIE1B) | (1 << OCIE1A) //enable both compare/match A & B OCR1A = 2000 //try to set OCR1A and OCR1B but it only loads the LOW byte Serial.print("TCNT1:#1 \t") Serial.println(TIM16_ReadTCNT1()) //reads only the LOW byte SREG = cSREG //enable interrupts to print an intermediate result Unsigned long int ISRmicrotimerCOMPB //interrupt time tagĬli() //stop interrupts before messing with internal registers Unsigned long int ISRmicrotimerCOMPA //interrupt time tag Here is the sketch I am using - it runs for a little over 2.5 sec (dominated by the delay statements): char cSREG //SREG storage I have been assuming (perhaps incorrectly) that the IDE includes the appropriate set of #defines and libraries that are required for support of the language. The example code assumes that the part specific header file is included." and I don't know what a "part specific header file" is or where I would look for it. There is a note toward the bottom of p152 that says "1. ![]() ![]() I want to write OCR1A and OCR1B to values greater than 256 but following the suggestions on p152/3 in the Atmel Datasheet I can't seem to get the results promised. Serial.In trying to understand how to use the 16-bit Timer1 correctly, I have run into a problem that must be very simple but is unyielding to all of my attempts to tease out a solution. Serial.print((mod.bmLeftGUI = 1) ? "G" : " ") Serial.print((mod.bmLeftAlt = 1) ? "A" : " ") Serial.print((mod.bmLeftShift = 1) ? "S" : " ") Serial.print((mod.bmLeftCtrl = 1) ? "C" : " ") Void KbdRptParser::PrintKey(uint8_t m, uint8_t key) Void OnKeyDown (uint8_t mod, uint8_t key) Void OnControlKeysChanged(uint8_t before, uint8_t after) Please contact us to get full sample codes: as HID Keyboard Device on the computer.Ĭlass KbdRptParser : public KeyboardReportParser Serial.println("OSCOKIRQ failed to assert") ![]() Serial.println("Please set the scanner to USB CDC mode") While (!Serial) // Wait for serial port to connect - used on Leonardo, Teensy and other boards with built-in USB CDC serial connection Satisfy the IDE, which needs to see the include statment in the ino too.ĮrrorMessage (PSTR("SetControlLineState"), rcode) ĮrrorMessage (PSTR("SetLineCoding"), rcode) Now you should be able to open all the examples codes by navigating to “File>Examples>USB_Host_Shield_20”, and then select the example.įor more information please visit the following sites: The final structure should look like this: Now move the “USB_Host_Shield_20” directory to the “libraries” directory. Open that directory and create a directory called “libraries” inside that directory. There you will see the location of your sketchbook. Now open up the Arduino IDE and open “File>Preferences”. Then uncompress the zip folder and rename the directory to “USB_Host_Shield_20”, as any special characters are not supported by the Arduino IDE. Please see the following page for instructions:įirst download the library by clicking on the following link: Please contact us to get full sample codes: as USB com port device on the computer.įirst, install Arduino IDE version 1.6.2 or newer, then simply use the Arduino Library Manager to install the library. PrintHex(buffer.c_str(), buffer.length()) If (buffer.indexOf(response) != -1 || buffer.equals(response)) ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |